Error Code	Error Name	Description
0	LJ_SUCCESS
200	LJME_WARNINGS_BEGIN	This indicates where the warning codes start is not a real warning code.
399	LJME_WARNINGS_END	This indicates where the warning codes end is not a real warning code.
201	LJME_FRAMES_OMITTED_DUE_TO_PACKET_SIZE	Some read/write operation(s) were not sent to the device because the Feedback command being created was too large for the device, given the current connection type.
202	LJME_DEBUG_LOG_FAILURE	The debug log file could not be written to. Check the LJM_DEBUG_LOG_FILE and related LJM configurations.
203	LJME_USING_DEFAULT_CALIBRATION	The device's calibration could not be read, so the nominal calibration values were used. Possible Cause: Incompatible microSD card installed. See SD Card section of T7 Datasheet.
204	LJME_DEBUG_LOG_FILE_NOT_OPEN	The message could not be logged because the debug log file has not been opened.
254	FEATURE_NOT_IMPLEMENTED
1200	LJME_MODBUS_ERRORS_BEGIN	This indicates where the Modbus error codes start is not a real Modbus error code.
1216	LJME_MODBUS_ERRORS_END	This indicates where the Modbus error codes end is not a real Modbus error code.
1201	LJME_MBE1_ILLEGAL_FUNCTION	The device received an invalid function code.
1202	LJME_MBE2_ILLEGAL_DATA_ADDRESS	The device received an invalid address. Alternatively, this error could indicate illegal access to a device register such as trying to write to a read only register.
1203	LJME_MBE3_ILLEGAL_DATA_VALUE	The device received a value that could not be written to the specified address.
1204	LJME_MBE4_SLAVE_DEVICE_FAILURE	The device encountered an error.
1205	LJME_MBE5_ACKNOWLEDGE	The device acknowledges the request, but will take some time to process.
1206	LJME_MBE6_SLAVE_DEVICE_BUSY	The device is busy and cannot respond currently.
1208	LJME_MBE8_MEMORY_PARITY_ERROR	The device detected a memory parity error.
1210	LJME_MBE10_GATEWAY_PATH_UNAVAILABLE	The requested route was not available.
1211	LJME_MBE11_GATEWAY_TARGET_NO_RESPONSE	The requested route was available but the device failed to respond.
1220	LJME_LIBRARY_ERRORS_BEGIN	This indicates where the LJM error codes start is not a real LJM error code.
1399	LJME_LIBRARY_ERRORS_END	This indicates where the LJM error codes end is not a real LJM error code.
1221	LJME_UNKNOWN_ERROR	LJM reached an unexpected state. Please contact LabJack support if you've received this error.
1222	LJME_INVALID_DEVICE_TYPE	LJM received an unsupported device type during device open or discovery.
1223	LJME_INVALID_HANDLE	LJM reached an invalid state due to an issue with an invalid handle reference.
1224	LJME_DEVICE_NOT_OPEN	The requested handle did not refer to an open device. Perhaps the Open call failed but you still tried to use the returned handle. Perhaps your code called Close somewhere and then after tried to use the handle.
1225	LJME_STREAM_NOT_INITIALIZED	The requested device does not have a stream initialized in LJM.
1226	LJME_DEVICE_DISCONNECTED	The device could not be contacted and LJM is not configured to heal device connections (see LJM config LJM_HEAL_CONNECTION_MODE).
1227	LJME_DEVICE_NOT_FOUND	A device matching the requested device parameters could not be found and therefore could not be opened. This could indicate an invalid parameter to a device open function or that the desired connection is already claimed/unavailable.
1228	LJME_APERIODIC_STREAM_OUT_NOT_INITIALIZED	There was an attempt to modify an aperiodic stream-out prior to its initialization.
1229	LJME_DEVICE_ALREADY_OPEN	The device being registered was already registered. Please contact LabJack support if you've received this error.
1230	LJME_DEVICE_CURRENTLY_CLAIMED_BY_ANOTHER_PROCESS	At least one matching device was found, but cannot be claimed by this process because a different process has already claimed it. Either close the device handle in your other process (i.e. program or application) or close the other process. Then try opening the device again.
1231	LJME_CANNOT_CONNECT	At least one device matching the requested device parameters was found, but a connection could not be established. Typically indicates a TCP socket connection issue.
1232	LJME_STREAM_OUT_INDEX_OUT_OF_RANGE	An invalid index value was passed to a stream-out function.
1233	LJME_SOCKET_LEVEL_ERROR	A TCP socket-level error occurred.
1234	LJME_SCAN_RATE_INCONSISTENT	The scan rate passed to a stream out function did not match the stream scan rate
1236	LJME_CANNOT_OPEN_DEVICE	The device could not be opened.
1237	LJME_CANNOT_DISCONNECT	An error occurred while attempting to disconnect.
1238	LJME_WINSOCK_FAILURE	A Windows WINSOCK error occurred.
1239	LJME_RECONNECT_FAILED	The device could not be contacted. LJM is configured to heal device connections and the reconnection attempt failed.
1240	LJME_CONNECTION_HAS_YIELDED_RECONNECT_FAILED	The device connection was yielded to another process and now cannot be contacted.
1241	LJME_USB_FAILURE	System USB communication failed fatally.
1242	LJME_STREAM_FLUSH_TIMEOUT	Stream flushing did not resolve before the timeout.
1243	LJME_U3_NOT_SUPPORTED_BY_LJM	LJM does not support UD-series LabJack devices; use the UD driver
1246	LJME_U6_NOT_SUPPORTED_BY_LJM	LJM does not support UD-series LabJack devices; use the UD driver
1249	LJME_UE9_NOT_SUPPORTED_BY_LJM	LJM does not support UD-series LabJack devices; use the UD driver
1250	LJME_INVALID_ADDRESS	The requested address did not match any address known to LJM (included in ljm_constants.json)
1251	LJME_INVALID_CONNECTION_TYPE	LJM received an unexpected connection type during device open or discovery.
1252	LJME_INVALID_DIRECTION	LJM received an unexpected read/write direction.
1253	LJME_INVALID_FUNCTION	LJM received an unexpected Modbus function.
1254	LJME_INVALID_NUM_REGISTERS	LJM received an unexpected number of registers.
1255	LJME_INVALID_PARAMETER	LJM received an unexpected parameter. Please check the LabJackM.h description of the function that returned this error for an explanation.
1256	LJME_INVALID_PROTOCOL_ID	LJM received an unexpected Modbus protocol ID.
1257	LJME_INVALID_TRANSACTION_ID	LJM received an unexpected Modbus transaction ID.
1258	LJME_NUM_WRITES_LARGER_THAN_AVAILABLE_SPACE	LJM received more values to stream out than are available in the LJM write queue.
1259	LJME_UNKNOWN_VALUE_TYPE	LJM received an unexpected data type.
1260	LJME_MEMORY_ALLOCATION_FAILURE	LJM was unable to allocate needed memory.
1261	LJME_NO_COMMAND_BYTES_SENT	No Modbus command bytes could be sent to the device.
1262	LJME_INCORRECT_NUM_COMMAND_BYTES_SENT	An incorrect number of Modbus command bytes were sent to the device, as reported by the underlying driver.
1263	LJME_NO_RESPONSE_BYTES_RECEIVED	No Modbus response bytes could be received from the device during the timeout period. Likely indicates some failure/unreliability with the communication method. See the Timeout Configs page in the LJM User's Guide for related information.
1264	LJME_INCORRECT_NUM_RESPONSE_BYTES_RECEIVED	An incorrect/unexpected number of Modbus response bytes were received from the device during the timeout period. Likely indicates some failure/unreliability with the communication method. See the Timeout Configs page in the LJM User's Guide for related information.
1265	LJME_MIXED_FORMAT_IP_ADDRESS	LJM received an IP identifier that seemed to be formatted in both hexadecimal and decimal.
1266	LJME_UNKNOWN_IDENTIFIER	LJM received an unknown identifier type during device open or discovery.
1267	LJME_NOT_IMPLEMENTED	An unimplemented functionality was attempted to be used. Please contact LabJack support if you've received this error so we can implement it for you!
1268	LJME_INVALID_INDEX	LJM received an index/offset that was out-of-bounds. Please contact LabJack support if you've received this error.
1269	LJME_INVALID_LENGTH	LJM received a length that did not make sense. Please contact LabJack support if you've received this error.
1270	LJME_ERROR_BIT_SET	A Modbus response had the error bit set. Please contact LabJack support if you've received this error.
1271	LJME_INVALID_MAXBYTESPERMBFB	LJM_AddressesToMBFB received a value of MaxBytesPerMBFB that was too small.
1272	LJME_NULL_POINTER	LJM received a null pointer for a pointer parameter that is required to not be null.
1273	LJME_NULL_OBJ	LJM found a null object. Please contact LabJack support if you've received this error.
1274	LJME_RESERVED_NAME	The requested name was invalid/reserved.
1275	LJME_UNPARSABLE_DEVICE_TYPE	LJM received a device type string that was unparsable or unexpected.
1276	LJME_UNPARSABLE_CONNECTION_TYPE	LJM received a connection type string that was unparsable or unexpected.
1277	LJME_UNPARSABLE_IDENTIFIER	LJM received a identifier string that was unparsable or unexpected.
1278	LJME_PACKET_SIZE_TOO_LARGE	The Modbus packet to be sent or the expected Modbus packet to be received exceeded the maximum packet size for the device connection.
1279	LJME_TRANSACTION_ID_ERR	LJM received a mismatched Modbus transaction ID from the device.
1280	LJME_PROTOCOL_ID_ERR	LJM received a mismatched Modbus protocol ID from the device.
1281	LJME_LENGTH_ERR	LJM received a mismatched Modbus packet length from the device.
1282	LJME_UNIT_ID_ERR	LJM received a mismatched Modbus unit ID from the device.
1283	LJME_FUNCTION_ERR	LJM received a mismatched Modbus function ID from the device.
1284	LJME_STARTING_REG_ERR	LJM received a mismatched Modbus register address from the device.
1285	LJME_NUM_REGS_ERR	LJM received a mismatched Modbus number of registers from the device.
1286	LJME_NUM_BYTES_ERR	LJM received a mismatched Modbus number of bytes from the device.
1289	LJME_CONFIG_FILE_NOT_FOUND	The LJM configuration file could not be opened for reading.
1290	LJME_CONFIG_PARSING_ERROR	An error occurred while parsing the LJM configuration file.
1291	LJME_INVALID_NUM_VALUES	LJM received an invalid number of values.
1292	LJME_CONSTANTS_FILE_NOT_FOUND	The LJM error constants file and/or Modbus constants file could not be opened for reading.
1293	LJME_INVALID_CONSTANTS_FILE	The LJM error constants file and/or Modbus constants file could not be parsed.
1294	LJME_INVALID_NAME	The requested name was not found in the register loaded from the constants file (if the constants file is loaded).
1296	LJME_OVERSPECIFIED_PORT	The requested connection type is ANY and port is specified.
1297	LJME_INTENT_NOT_READY	The internal operation object was not prepared correctly. Please contact LabJack support if you've received this error.
1298	LJME_ATTR_LOAD_COMM_FAILURE	A device matching the requested device parameters was found, claimed, and connected, but a communication error prevented device attributes from being loaded to LJM. The device was not opened. Likely indicates some failure/unreliability with the communication method.
1299	LJME_INVALID_CONFIG_NAME	LJM received an unknown configuration name.
1300	LJME_ERROR_RETRIEVAL_FAILURE	An error occurred on the device and LJM was unable to retrieve more information about that error. Please contact LabJack support if you've received this error.
1301	LJME_LJM_BUFFER_FULL	The LJM stream buffer was filled with stream data and stream was stopped. See https://labjack.com/support/software/api/ljm/streaming-lots-of-9999-values
1302	LJME_COULD_NOT_START_STREAM	LJM could not start stream. Input may have incorrect or a different error may have occurred.
1303	LJME_STREAM_NOT_RUNNING	Stream data was attempted to be accessed when LJM was not streaming data to/from the device.
1304	LJME_UNABLE_TO_STOP_STREAM	The stream could not be stopped.
1305	LJME_INVALID_VALUE	LJM received a value that was not expected.
1306	LJME_SYNCHRONIZATION_TIMEOUT	LJM did not receive data from the device for longer than the timeout specified by LJM_STREAM_RECEIVE_TIMEOUT_MS. Often returned in relation to externally clocked stream modes. See the eStreamStart documentation in the LJM User's Guide.
1307	LJME_OLD_FIRMWARE	The current firmware version of the device was not sufficient to read/write a requested register, as according to the loaded LJM constants file.
1308	LJME_CANNOT_READ_OUT_ONLY_STREAM	The stream running is out-only and does not produce data values.
1309	LJME_NO_SCANS_RETURNED	The LJM configuration LJM_STREAM_SCANS_RETURN is set to LJM_STREAM_SCANS_RETURN_ALL_OR_NONE and the full ScansPerRead scans have not be received.
1310	LJME_TEMPERATURE_OUT_OF_RANGE	LJM_TCVoltsToTemp received a temperature that was out of range for the given thermocouple type.
1311	LJME_VOLTAGE_OUT_OF_RANGE	LJM_TCVoltsToTemp received a voltage that was out of range for the given thermocouple type.
1312	LJME_FUNCTION_DOES_NOT_SUPPORT_THIS_TYPE	The function does not support the given data type. For example, LJM_eReadName and LJM_eReadAddress do not support reading LJM_STRING values, which are too large.
1313	LJME_INVALID_INFO_HANDLE	The given info handle did not exist. (It may have been passed to LJM_CleanInfo already.)
1314	LJME_NO_DEVICES_FOUND	An Open/OpenS call was called - with any device type, any connection type, and any identifier - but no devices were found.
1316	LJME_AUTO_IPS_FILE_NOT_FOUND	The LJM auto IPs file could not be found or read. LJM will attempt to create the auto IPs file, as needed.
1317	LJME_AUTO_IPS_FILE_INVALID	The LJM auto IPs file contents were not valid.
1318	LJME_INVALID_INTERVAL_HANDLE	The given interval handle did not exist.
1319	LJME_NAMED_MUTEX_PERMISSION_DENIED	There was a permission error while accessing a system-level named mutex. Try restarting your computer.
1320	LJME_DIGITAL_AUTO_RECOVERY_ERROR_DETECTED	During stream, the device buffer overflowed, causing auto-recovery to occur. See the digital stream information in the Stream Configs section of the LJM User's Guide.
1321	LJME_NEGATIVE_RECEIVE_BUFFER_SIZE	During stream, the receive buffer size was negative. This is probably because LJM_STREAM_TCP_RECEIVE_BUFFER_SIZE was set to too large a number to be represented by the signed data type being used, int. Solution: Use a smaller LJM_STREAM_TCP_RECEIVE_BUFFER_SIZE.
2012	FEATURE_NOT_SUPPORTED	Feature is not supported on this device.
2300	MODBUS_RSP_OVERFLOW	Response packet greater than max packet size.
2301	MODBUS_CMD_OVERFLOW	Command packet greater than max packet size
2310	MODBUS_STRING_CMD_TOO_BIG
2311	MODBUS_STRING_PARAM_TOO_BIG
2312	MODBUS_STRING_BAD_NUM_PARAMS
2313	MODBUS_INVALID_NUM_REGISTERS	Register data types does not match the number of registers in the request.
2314	MODBUS_READ_TOO_LARGE
2315	MODBUS_NUM_REGS_MUST_BE_EVEN	Register or group of registers requires the access be in an even number of registers.
2316	MODBUS_STRING_MISSING_NULL	Strings must be terminated with a null (\0, 0x00).
2317	UDP_DISCOVERY_ONLY_MODE_IS_ENABLED	The UDP discovery socket has been set to discovery only. Only a few registers may be read while in this mode.
2330	STARTUP_CONFIG_INVALID_CODE
2331	STARTUP_CONFIG_INVALID_READ	An attempt was made to read beyond the configuration structure.
2340	USER_RAM_FIFO_MUST_BE_EMPTY	The FIFO can not contain any data when data size is being changed.
2343	USER_RAM_FIFO_INSUFFICIENT_VALUES	The FIFO contains fewer values than requested.
2344	USER_RAM_FIFO_INSUFFICIENT_SPACE	FIFO does not have enough free space to hold the requested write. No data was added to the FIFO.
2345	USER_RAM_FIFO_SIZE_MUST_BE_EVEN	The number of bytes allocated to the FIFO must be even..
2350	INTFLASH_ADD_INVALID
2351	INTFLASH_CODE_INVALID
2352	INTFLASH_OP_PROHIBITED	Attempted to read or write a section that is not allowed.
2353	INTFLASH_SECTION_OVERWRITE	Attempted to write or read beyond the currently selected section.
2354	INTFLASH_KEY_INVALID	Specified Key and Address mismatch.
2355	FLASH_VERIFICATION_FAILED	A write to flash failed to set one or more bits to the desired values.
2356	FLASH_ERASE_FAILED	One or more bits failed to set during a flash erase operation.
2358	INTFLASH_UNAVAILABLE	Flash can not be accessed due to the WiFi module booting up.
2359	FILEIO_UNAVAILABLE	The file system can not be accessed due to the WiFi module booting up.
2370	AIN_RANGE_INVALID	Specified range not available on this device.
2371	AIN_SETTLING_INVALID	Specified settling is greater than device max.
2372	AIN_SET_TO_BINARY	Analog input system currently set to binary. Some operations, such as AIN_EF, will fail.
2373	AIN_NEGATIVE_CHANNEL_INVALID	For channel range 0-13: Negative channel must be even channel number + 1. For extended channel range 48-127: Negative channel must be channel number + 8.
2374	AIN_ALL_ZERO_ONLY	Only a value of zero may be written to this address.
2375	AIN_RESOLUTION_INVALID	Selected resolution is invalid. Valid range is 0-5 for T4 and 0-12 for T7.
2376	AIN_RATE_INVALID	The selected AIN rate configuration is invalid for the desired resolution index or vise-versa.
2377	AIN_CHN_DISABLED	The AIN channel has been disabled
2380	LUA_VM_STATE_NO_CHANGE
2381	LUA_INITIALIZATION_ERROR
2382	LUA_INVALID_NUM_IO_FLOATS	Requested more than the max possible number of IO floats.
2383	LUA_IO_FLOATMEM_OVERFLOW	Attempt to read/write beyond the currently allocated IO space.
2384	LUA_INVALID_MODE
2385	LUA_IS_RUNNING	A running script is preventing the requested operation.
2386	LUA_CODE_BUFFER_EMPTY	Attempted to run a program that is not present.
2387	LUA_DEBUG_IS_DISABLED	Attempted to read from debug buffer while debug is disabled.
2388	LUA_TABLE_SMALLER_THAN_SPECIFIED_SIZE	The Lua table provided is too small to process the request.
2389	LUA_IS_CLOSING	The Lua VM is being closed, usually takes less than 100 ms.
2400	SYSTEM_MEMORY_BEREFT	Insufficient RAM to perform the requested action. Often occurs when a loaded Lua script is too large.
2401	SYSTEM_MEMORY_OVERWRITE	Attempted to overwrite a buffer.
2402	SYSTEM_REBOOT_CODE_INVALID	Invalid code supplied when issuing a reboot.
2403	SYSTEM_READ_OVERRUN
2404	SYSTEM_INVALID_PIN
2405	SYSTEM_NVRAM_UNAVAILABLE	NVRAM is not available on this device.
2406	SYSTEM_NVRAM_INVALID_ADDRESS	The specified NVRAM location is not available on this device.
2407	SYSTEM_WAIT_TOO_LONG	The requested wait time is beyond the max allowed.
2408	SYSTEM_INCOMPATIBLE_FIRMWARE_VERSION	The firmware image is not compatible with this device. Typically due to flash chip incompatibility.
2420	DEVICE_NAME_MUST_BE_ALPHANUM	Attempted to write a device name with invalid characters.
2450	POWER_INVALID_SETTING	Unknown value specified.
2451	POWER_USB_NEEDS_20MHZ_OR_MORE	Core must be running at 20MHz minimum for USB to operate.
2452	POWER_ETH_NEEDS_20MHZ_OR_MORE	Core must be running at 20MHz minimum for Ethernet to operate.
2453	POWER_AIN_NEEDS_20MHZ_OR_MORE	Core must be running at 20MHz minimum for AIN to operate.
2454	POWER_STREAM_NEEDS_20MHZ_OR_MORE	Core must be running at 20MHz minimum to use stream mode.
2455	POWER_SD_NEEDS_20MHZ_OR_MORE	Core must be running at 20MHz minimum to use the SD card.
2456	POWER_CAN_NOT_CHANGE_USED_CONNECTION	Can not change the power level of the connected medium.
2459	POWER_NO_CHANGE	The written power mode is the same as the current setting.
2460	POWER_ANALOG_OFF	Analog input system is powered down.
2490	WIFI_NOT_ASSOCIATED	WiFi needs to be connected to a network before the requested action can be performed.
2500	HW_DIO_NOT_AVAILABLE
2501	DIO_SET_TO_ANALOG	The digital line addressed is set to analog. Digital operations cannot be performed.
2508	HW_CNTRA_NOT_AVAILABLE	Counter A is being used by another system. Typically this is due to a high speed counter being enabled while trying to enable a DIO_EF clock that requires the same resource or vise-versa
2509	HW_CNTRB_NOT_AVAILABLE	Counter B is being used by another system. Typically this is due to a high speed counter being enabled while trying to enable a DIO_EF clock that requires the same resource or vise-versa
2510	HW_CNTRC_NOT_AVAILABLE	Counter C is being used by another system.
2511	HW_CNTRD_NOT_AVAILABLE	Counter D is being used by another system. Typically this is due to a high speed counter that shares a resource with the stream clock being enabled while trying to enable stream mode or vise-versa
2520	HW_CIO0_NOT_AVAILABLE
2521	HW_CIO1_NOT_AVAILABLE
2523	HW_DAC1_NOT_AVAILABLE	DAC1 is an active stream out target and therefore unavailable.
2524	HW_LEDS_NOT_AVAILABLE	The LEDs cannot be controlled when the LED power mode is not set to manual.
2550	EF_DIO_HAS_NO_TNC_FEATURES	The DIO accessed does not support any extended features.
2551	EF_INVALID_TYPE	The selected type is not recognized.
2552	EF_TYPE_NOT_SUPPORTED	The selected type is not recognized.
2553	EF_PIN_TYPE_MISMATCH	The requested type is not supported on this DIO pin.
2554	EF_CLOCK_SOURCE_NOT_ENABLED	Attempted to disable a clock source that is not running.
2555	EF_32BIT_DATA_INTO_16BIT_REG	A number greater than 16-bits was written to a clock source configured for 16-bits. Commonly occurs when an incorrect value is applied to CONFIG_A or CONFIG_B for an output feature such as PWM or pulse output.
2556	EF_SET_TO_32BIT
2557	EF_SMOOTH_VALUE_OUT_OF_RANGE
2558	EF_32BIT_REQUIRES_BOTH_CLOCK0and1	Both Clock_Source 1 and Clock_Source 2 must be disabled before enabling Clock_Source 0.
2559	EF_DIVISOR_VALUE_INVALID	The specified divisor value is not supported. Supported values are: 1,2,4,8,16,32,64,256. This code was formerly named EF_PRESCALE_VALUE_INVALID
2560	EF_PIN_RESERVED	The pin is already in use by another system.
2561	EF_INVALID_DIO_NUMBER	The specified DIO_EF address is not supported on this device.
2563	EF_LINE_MUST_BE_LOW_BEFORE_STARTING	The DIO line must be set to output low to ensure proper signal generation.
2564	EF_INVALID_DIVISOR
2565	EF_VALUE_GREATER_THAN_PERIOD	The DIO_EF_CONFIG value written determines a DIO line transition point relative to the count of a ClockSource. To prevent signal glitches, the value must be less than the selected ClockSource's roll value.
2566	EF_CAN_NOT_CHANGE_INDEX_WHILE_ENABLED	The index of a DIO_EF can not be changed while that DIO_EF is enabled.
2580	AIN_EF_INVALID_TYPE	The specified type index is not supported.
2581	AIN_EF_INVALID_NUM_SAMPLES	Too many samples specified.
2582	AIN_EF_CALCULATION_ERROR
2583	AIN_EF_CHANNEL_INACTIVE	The AIN_EF channel has not been initialized. To initialize, set the index configuration to a non-zero value.
2584	AIN_EF_CALCULATION_OUT_OF_RANGE	The final value calculated for the AIN_EF is outside of the range the feature supports. This often indicates that there is some configuration issue.
2585	AIN_EF_INVALID_CHANNEL	AIN_EF is not supported on the specified channel, or the specified channel does not exist.
2586	AIN_EF_INVALID_CJC_REGISTER	The register address specified for CJC measurement is not supported.
2587	AIN_EF_STREAM_START_FAILURE	Could not start the data collection stream.
2588	AIN_EF_COULD_NOT_FIND_PERIOD	Failed to detect a period to perform calculations over.
2589	AIN_EF_MUST_BE_DIFFERENTIAL	The selected AIN must be set to differential.
2590	AIN_EF_SCAN_TIME_TOO_LONG	The data collection time (number of samples / scan_rate) is too big. Limit is set to 180 ms.
2591	AIN_EF_INVALID_EXCITATION_INDEX	The excitation circuit index specified is not valid, use a different excitation circuit.
2600	STREAM_NEED_AT_LEAST_ONE_CHN	The list of channels to stream is empty.
2601	STREAM_CLOCK_BASE_NOT_WRITABLE	The stream clock base is read only.
2602	STREAM_EXTCLK_AND_GATE_MX
2603	STREAM_IN_SPONTANEOUS_MODE	Stream data can not be read with commands while in spontaneous mode.
2604	STREAM_USB_PKT_OVERFLOW	STREAM_SAMPLES_PER_PACKET is set to a value greater than the USB interface can support.
2605	STREAM_IS_ACTIVE	The requested operation can not be performed while stream is running.
2606	STREAM_CONFIG_INVALID	Stream resolution can not be greater than 8.
2607	STREAM_CHN_LIST_INVALID	The channel list contains an unstreamable address.
2608	STREAM_SCAN_RATE_INVALID	The scan rate times the number of channels per scan is too great for this device.
2609	STREAM_OUT_BUFF_TOO_BIG
2610	STREAM_OUT_NUM_INVALID	An invalid stream out number was specified.
2611	STREAM_DATA_TYPE_INVALID	An unsupported data types was specified.
2612	STREAM_TARGET_CONFIG_INVALID	Stream must be set to either spontaneous or command-response.
2613	STREAM_OUT_BUFF_FULL	Attempted to write more data than the buffer can hold. Extra data was discarded.
2614	STREAM_OUT_TARGET_INVALID	The specified address cannot be a stream out target.
2615	STREAM_BUFF_SIZE_INVALID	The specified buffer was either too large or was not a power of 2.
2616	STREAM_OUT_BUFF_LOOP_OVERWRITE
2617	STREAM_OUT_BUFF_DNE	The buffer size must be set before data can be written to it.
2618	STREAM_SAMPLES_PER_PKT_INVALID	The specified number of samples per packet is too large.
2619	STREAM_BUFFER_DNE
2620	STREAM_NOT_RUNNING	Stream was already disabled.
2621	STREAM_SETTLING_INVALID	Specified settling time is greater than the max possible.
2622	STREAM_OUT_LOOP_TOO_BIG	The loop size is too big for the current buffer size.
2623	STREAM_OUT_DATA_TRGT_MISSMATCH	There is a mismatch between the stream out buffer type and target register.
2624	STREAM_INVALID_DIVISOR	Selected divisor can not be used.
2625	STREAM_CHN_CAN_NOT_BE_STREAMED	The requested channel can not be streamed.
2626	STREAM_OUT_DAC_IN_USE	The high resolution converter cannot be used while stream out is used to update a DAC.
2627	STREAM_OUT_NEEDS_TO_BE_ENABLED	The STREAM_OUT#_ENABLE register must be set to 1 before writing STREAM_OUT#_LOOP_NUM_VALUES, STREAM_OUT#_SET_LOOP, or any of the STREAM_OUT#_BUFFER_ registers.
2628	CANNOT_STREAM_FAST_WITH_DAC1_FREQUENCY_OUT_ENABLED	DAC1_FREQUENCY_OUT_ENABLE should be disabled before streaming at rates above 10kHz due to poor frequency output performance at higher stream rates.
2629	CANNOT_ENABLE_DAC1_FREQUENCY_OUT_WITH_FAST_STREAM	DAC1_FREQUENCY_OUT_ENABLE should not be enabled while streaming at rates above 10kHz due to poor frequency output performance at higher stream rates.
2630	STREAM_TRIGGER_INDEX_INVALID	The stream trigger index is not valid for this device
2670	SWDT_ROLLT_INVALID	The specified Software Watchdog timeout is too short.
2671	SWDT_ENABLED	The watchdog must be disabled before the requested operation can be performed.
2672	SWDT_DIO_SETTINGS_INVALID	The specified Software Watchdog DIO configurations are not valid.
2673	SWDT_DAC0_SETTINGS_INVALID	The specified Software Watchdog DAC0 configurations are not valid.
2674	SWDT_DAC1_SETTINGS_INVALID	The specified Software Watchdog DAC1 configurations are not valid.
2690	RTC_TIME_INVALID
2691	RTC_SNTP_TIME_INVALID	The specified SNTP update interval is too short.
2692	RTC_NOT_PRESENT	The requested operation can not be performed on units without a real-time-clock.
2700	SPI_MODE_INVALID	Valid modes are 0-3.
2701	SPI_NO_DATA_AVAILABLE	SPI RX data is not available in the RX buffer.
2702	SPI_CS_PIN_INVALID	Attempted to set an invalid pin.
2703	SPI_CLK_PIN_INVALID	Attempted to set an invalid pin.
2704	SPI_MISO_PIN_INVALID	Attempted to set an invalid pin.
2705	SPI_MOSI_PIN_INVALID	Attempted to set an invalid pin.
2706	SPI_CS_PIN_RESERVED	Selected pin is not available.
2707	SPI_CLK_PIN_RESERVED	Selected pin is not available.
2708	SPI_MISO_PIN_RESERVED	Selected pin is not available.
2709	SPI_MOSI_PIN_RESERVED	Selected pin is not available.
2710	SPI_TRANSFER_SIZE_TOO_LARGE	The specified TX buffer size is too large.
2720	I2C_BUS_BUSY	One or both of the I2C lines are held low. Check hardware and reset the bus.
2721	I2C_NO_DATA_AVAILABLE	Attempted to read from an empty buffer.
2722	I2C_SDA_PIN_INVALID	Attempted to set an invalid pin.
2723	I2C_SCL_PIN_INVALID	Attempted to set an invalid pin.
2724	I2C_SDA_PIN_RESERVED	The selected pin is not available.
2725	I2C_SCL_PIN_RESERVED	The selected pin is not available.
2726	I2C_TX_SIZE_TOO_LARGE	The specified TX buffer size is too large.
2727	I2C_RX_SIZE_TOO_LARGE	The specified RX buffer size is too large.
2728	I2C_BUFFER_OVERRUN	The data that was attempted to be written to the I2C TX buffer exceeded the maximum TX buffer size. Only data up to the maximum buffer size was placed in the TX buffer.
2729	I2C_SPEED_TOO_LOW	The throttle setting is too low, watchdog may fire. Minimum value = 46000
2740	SBUS_COMM_TIME_OUT	Slave device did not respond.
2741	SBUS_NO_ACK	Slave device did not acknowledge the data transfer.
2742	SBUS_CUSTOM_MODE_INVALID
2743	SBUS_INVALID_DIO_NUM	Attempted to set an invalid pin.
2744	SBUS_BACKGROUND_SERVICE_ON	Command-response reads can not be used while the background service is running.
2745	SBUS_CHECKSUM_ERROR	SHT communication checksum failed.
2760	TDAC_SDA_SCL_INVALID	SCL must be even and SDA must be SCL+1.
2761	TDAC_SCL_INVALID	Attempted to set an invalid pin.
2762	TDAC_INVALID_CHANNEL	The specified channel not supported on this device.
2763	TDAC_CAL_READ_FAILURE	Failed to read the TDAC calibration.
2764	TDAC_NOT_FOUND	The TDAC did not respond to communication attempts.
2770	ONEWIRE_UNSUPPORTED_FUNCTION	Unknown function specified.
2771	ONEWIRE_NO_PRESENCE_PULSE	Unable to detect any devices on the bus.
2780	ASYNCH_NUM_DATA_BITS_INVALID	The specified number of data bits is not supported.
2781	ASYNCH_NUM_TO_WRITE_INVALID	The number of bytes to send is invalid.
2782	ASYNCH_READ_BUFF_SIZE_INVALID	The specified buffer size is invalid. Max is 2048.
2783	ASYNCH_BAUD_TOO_HIGH	The baud rate is too high for this device.
2784	ASYNCH_IS_ENABLED	The specified operation can not be performed while enabled.
2785	ASYNCH_IS_NOT_ENABLED	The specified operation can not be performed while disabled.
2786	ASYNCH_TX_BUFFER_FULL	The transmit buffer is full.
2787	ASYNCH_TX_TIMEOUT	Transmission timed out. Do not write more than 100 ms at a time.
2788	ASYNCH_BAUD_ZERO	The baud rate is zero. Please specify a baud rate.
2801	FILE_IO_DISK_ERROR	A hard error occurred in the low level disk I/O layer.
2802	FILE_IO_INTERNAL_ERROR	Assertion failed.
2803	FILE_IO_NOT_READY	The physical drive cannot work.
2804	FILE_IO_NO_FILE	Could not find the file.
2805	FILE_IO_NO_PATH	Could not find the path.
2806	FILE_IO_PATH_NAME_INVALID	The path name format is invalid.
2807	FILE_IO_DENIED	Access denied due to prohibited access or the directory is full.
2808	FILE_IO_EXIST	Access denied due to prohibited access.
2809	FILE_IO_INVALID_OBJECT	The file/directory object is invalid. In the context of performing an "ls" command, this indicates that there are no more files.
2810	FILE_IO_WRITE_PROTECTED	The physical drive is write protected.
2811	FILE_IO_INVALID_DRIVE	The logical drive number is invalid.
2812	FILE_IO_NOT_ENABLED	The volume has no work area.
2813	FILE_IO_NO_FILESYSTEM	There is no valid FAT12, FAT16, or FAT32 volume.
2814	FILE_IO_MKFS_ABORTED	The f_mkfs() function aborted due to any parameter error.
2815	FILE_IO_TIMEOUT	Could not get granted access to the volume within the defined timeout period.
2816	FILE_IO_LOCKED	The operation is rejected according to the file sharing policy.
2817	FILE_IO_NOT_ENOUGH_CORE	LFN working buffer could not be allocated.
2818	FILE_IO_TOO_MANY_OPEN_FILES	The number of open files is greater than the allowable limit (files > _FS_SHARE).
2819	FILE_IO_INVALID_PARAMETER	The given parameter is invalid.
2900	WIFI_ASSOCIATED	The WiFi module associated to the network.
2901	WIFI_ASSOCIATING	The WiFi module is attempting to associate to the network.
2902	WIFI_ASSOCIATION_FAILED	The WiFi module failed to associate to the network.
2903	WIFI_UNPOWERED	The WiFi module is not currently powered.
2904	WIFI_BOOTING_UP	The WiFi module is initializing.
2905	WIFI_COULD_NOT_START	The WiFi module was unable to properly initialize.
2906	WIFI_APPLYING_SETTINGS	The WiFi module is attempting to apply the desired network settings.
2907	WIFI_DHCP_STARTED	The WiFi module has begun the process of claiming a DHCP lease.
2909	WIFI_OTHER	The WiFi module is in an unspecified state.
2920	WIFI_UPDATE_CONFIG	The WiFi module is getting ready to start an update.
2921	WIFI_UPDATE_IN_PROG	The WiFi module is in the process of updating.
2923	WIFI_UPDATE_REBOOT	The WiFi module has updated and will restart to apply the new changes.
2924	WIFI_UPDATE_SUCCESS	The WiFi module was successfully updated.
2925	WIFI_UPDATE_FAILED	The WiFi module was not successfully updated.
2940	STREAM_AUTO_RECOVER_ACTIVE	The stream buffer reached its capacity and auto-recovery has begun to avoid an overflow. No new samples will be saved until there is free space in the buffer.
2941	STREAM_AUTO_RECOVER_END	There is space available in the stream buffer for new samples again and auto-recovery has ended.
2942	STREAM_SCAN_OVERLAP	A new scan started before the previous scan finished. Generally occurs because ScanRate > MaxSampleRate/NumChannels. Note that MaxSampleRate is impacted by Range, ResolutionIndex, and Settling. Try adding commands right before StreamStart to set AIN_ALL_RANGE=10, STREAM_RESOLUTION_INDEX=0, and STREAM_SETTLING_US=0.
2943	STREAM_AUTO_RECOVER_END_OVERFLOW	During stream auto-recovery, the variable tracking the number of skipped scans has reached an overflow condition.
2944	STREAM_BURST_COMPLETE	The specified number of stream scans have been acquired, stream will be stopped automatically.
2945	STREAM_BUFFER_FULL	The stream buffer reached capacity while auto-recovery was disabled. Stream has been stopped.
2950	SELFDIAG_MAIN_OSC_FAIL
2960	FILE_IO_NOT_FOUND	The requested file was not found.
2961	FILE_IO_NO_DISK	No SD card present or SC card could not be initialized.
2962	FILE_IO_INVALID_NAME	The file name is invalid.
2963	FILE_IO_FILE_NOT_OPEN	An open file is required to perform the requested operation.
2964	FILE_IO_TOO_MANY_OPEN	There are too many files open.
2965	FILE_IO_SD_CARD_NOT_FOUND	Failed to mount the SD card. Card may be bad or incompatible.
2966	FILE_IO_END_OF_CWD	There are no more files in the current working directory.